What is a V-belt?

A V-belt is a wedge-shaped belt manufactured out a rubber compound, reinforced with a tensile cord specifically engineered to transmit power into movement. V-belts can be found in driving mechanisms, such as engines in air compressors, fans, and pumps.

megadynegroup.com - How to Identify a V-Belt | Megadyne Group

Is a womens 10 a small or medium?

This varies from brand to brand and by country. Some stores will consider a medium to be a size 10, while others a size 12-14. As an average, a...

Last updated Jan 1, 2018

Do jowls go away with weight loss?

If you are overweight, sensible dieting and a regular cardiovascular workout will burn fat from all areas, including your face. For some people,...

Last updated Mar 25, 2018

Promotion

V-Belt Product Types

There are a number of possible types of V-belts available

Light Duty - Suitable for light duty applications normally using fractional horsepower motors

Classical Heavy Duty - Wide range of sizes

Molded Cogged - Cogs allow use of smaller diameter pulleys and provide heat dissipation; Raw Edge Sidewalls prevent slippage Wedge - Narrower, deeper profile with higher power capacity than classical v-belt; allows for smaller, more compact drives Wedge Cogged - Same properties as Wedge, but cogged for greater flexibility and heat dissipation Banded – Two or more v-belts joined to form a single belt allowing the belts to function as a single belt with equal load distribution and wear

How to Identify a V-Belt

Belts with Branding

If the branding on the v-belt is still intact, the easiest way to identify it is to simply read the part number. Unfortunately, after hours of use the brand is often worn off and not legible. In this case, it becomes necessary to take note of the dimensions of the belt.

Belts without Branding

You then need to find the measurements for your V-belt. The following steps will allow you to do so:

Step 1: Determine Belt Cross Section

V-belt cross sections are categorized based on their top width and depth measurements. Each width/depth combination is labeled using a letter of the alphabet. For example, v-belts with 21/32 in. width and 7/16 in. depth is labeled a "B" belt. Specially designed Browning V-Belt Rules are also available with a gauge to help you select the correct belt type.

Step 2: Identify Belt Construction

How much magnesium do I need daily to lose weight?

adults 19-30 years: men 400 milligrams (mg), women 310 mg. adults 31+: men 420 mg, women 320 mg.

Last updated Feb 4, 2019

What medicine is the same as Ozempic?

Rybelsus and Ozempic contain the same active drug, semaglutide, but in different forms. Rybelsus comes as an oral tablet, while Ozempic is given as...

Last updated Nov 8, 2021

Promotion

V-belts are available in either wrapped or raw edge styles. A conventional wrapped v-belt will have an envelope of rubberized fabric covering the belt. A raw edge cogged v-belt will have exposed rubber sidewalls and molded cogs on the bottom that resemble teeth. The following characteristics may also be present, depending on the construction type: Rubberized fabric cover – Cover envelopes entire belt and protects the belt core Top fabric – Provides heat and oil resistance Load carrying section – Cords (also known as tensile members) give the ability to transmit power and ensure uniform load distribution Compression section – Elastomer resists compression fatigue and dissipates internal heat build-up, providing firm lateral pressure against sheave/pulley sidewall and distributes the load to the cords. Precision molded cogs – Provide additional flexibility, allowing for use of smaller pulley diameters, aiding in heat dissipation.

Step 3: Measure V-belt length

The most difficult part of identifying a v-belt is measuring the length. There is no precise method that is practical to perform in the field for v-belt measurement. Precise measurement requires a measuring fixture with pulleys of prescribed dimension and the ability to apply a specific tension to the belt according to ARPM (Association for Rubber Product Manufacturers) standards for the given belt section. Additionally, there are a number of terms used in the industry to describe length (e.g. inside length, outside length, pitch length, effective length) making it very confusing. Some belt providers instruct end users to utilize tapes to measure outside length. While this method can approximate belt length, it can still be off by inches. If the drive has ample installation and take-up range, using a tape can yield a belt that will fit the drive in many cases, however, there is no guarantee it is the optimum length designed for the drive. Knowing certain parameters of the drive in question, the correct length can be calculated. An easy way to perform the length calculation is to register for our free online drive design software, Product Selection Pro www.megadyne.productselectionpro.com

Can lemon and water reduce belly fat?

Does lemon water reduce belly fat? A. Lemon water can promote fullness, support hydration, boost metabolism, and increase weight loss. However,...

Last updated May 18, 2018

What are 20 protein foods?

20 Protein-Rich Foods for A Healthy Life Eggs: Eggs are the ideal dietary item to consume to maintain a lean physique. ... Almonds: Fibre, vitamin...

Last updated Jul 29, 2021

Promotion

Using Megadyne Product Selection Pro to perform a drive analysis will give an accurate length measurement as well as confirm whether the belt selected is appropriate for the application. Additionally, it provides the correct tension values to ensure the drive operates with maximum efficiency. Another option for end users who are not comfortable using drive design software is to contact Megadyne Application Engineering, who will work with you to perform the drive analysis and ensure the belts we deliver are the best choice for your application.

Step 4: Label the Drive

Finally, to avoid the issue of identifying the v-belt each time it needs to be replaced, a good maintenance practice is to properly label the drive with the correct belt part number. Use an adhesive sticker or any type of permanent signage where you can easily read the belt part number, making it easy to obtain belts in the future. Recording the date when the belts were installed can also enhance your maintenance program with increased uptime by knowing when to replace belts before they fail.

Quality V-Belts From Megadyne

Megadyne is pleased to offer a variety of v-belts, including rubber wrapped, rubber raw edge, banded, and linked v-belts, to meet the needs of a wide range of applications. We are proud to provide quality rubber and synthetic v-belts for automotive and tire applications, commercial and domestic appliances, and construction and industrial equipment. To learn more about Megadyne's extensive selection of v-belts, contact us today.

megadynegroup.com - How to Identify a V-Belt | Megadyne Group

What 3 foods to cut out to lose weight?

11 Foods to Avoid When Trying to Lose Weight The foods you eat can have a major effect on your weight. ... French Fries and Potato Chips. ......

Last updated Sep 5, 2019

Is it hard to lose waist fat?

One reason belly fat is so hard to lose is that it's considered an “active fat.” Unlike some fatty tissue that simply sits “dormant,” belly fat...

Last updated Jul 14, 2021

Promotion

What are the cons of Saxenda?

The most common side effects of Saxenda® in adults include nausea, diarrhea, constipation, vomiting, injection site reaction, low blood sugar...

Last updated Nov 5, 2020

Learn More »

Promotion

How to lose 10kgs in 3 weeks?

How To Lose 10 Kilograms In 3 Weeks Try Lemon Juice or Lemon Water. First, you can try to drink lemon juice in the morning. ... Eat Dinner Earlier....

Last updated Jan 5, 2022