How tight should a belt tension be?

Belt Tension Belt slippage hampers performance because accessories don't function properly. Belts that are too tight put an excessive load on pulleys, shafts, and bearings. Excessive belt tension will also wear out a belt quickly. Proper belt tension is 1/2 inch of sideplay both ways.

motortrend.com - Setting Proper Belt Alignment and Fit - Belt One On - MotorTrend

Does adding honey to green tea reduce benefits?

While green tea is already beneficial and health promoting on its own, adding some honey to your cup of green tea can make it more nourishing for...

Last updated Nov 12, 2018

Is it better to go to bed hungry or full?

“For optimal sleep it's best not to go to bed too hungry or too full,” says Lisa Moskovitz, R.D. On one hand, falling asleep when all you can think...

Last updated May 25, 2018

Promotion

See all 9 photos See all 9 photos

The most common reasons for belt failure are improper belt tension (too loose or too tight), poor alignment, pulley damage or distortion, environment (excessive heat and ozone), and using an improper belt for the application. Another issue is belt selection. Belt width and pulley width must match in every respect for proper function. Width match is important because there should be full contact (traction) between the belt and pulley. Unless you've performed an upgrade to a serpentine beltdrive, your classic Ford is fitted with a V beltdrive common on all cars and trucks prior to the '80s. The V-belt design lends itself to strength and power because a V-belt is triangular. What's more, its shape increases contact area, giving increased traction on two sides instead of one. Like tires, V-belts consist of rubber composition and cords wrapped inside a flexible extruded cover. Synthetic fiber cord is what gives the belt strength. Both rubber and cord work together in composite fashion to transfer power and deliver strength. In one sense, they work like bicycle chains-there's a tension (tight) side and a slack (loose) side. The tension side is the torque side, where pulling power is transmitted. The slack side feeds the tension side. This cycle of tension and slack is what challenges a belt most. See all 9 photos See all 9 photos Cog belts provide improved traction and cooling due to increased surface area. Improved belt traction means less slippage and heat. Today, manufacturers put cogs/ribs on the outside for even better performance. This belt style has proven itself quite well in regular use. When selecting a belt, you want a perfect fit in the pulley sheath. Belt and sheath walls should mate perfectly and without gaps. Think of belt-wall contact as you would tire contact with the road. The more contact between belt and sheath, the more traction your belt will have.

Belt Tension

Belt tension has everything to do with performance and reliability. Belt slippage hampers performance because accessories don't function properly. Belts that are too tight put an excessive load on pulleys, shafts, and bearings. Excessive belt tension will also wear out a belt quickly. Proper belt tension is 1/2 inch of sideplay both ways. Press down on the belt midway between pulleys and observe the travel. Belt tension should be checked on the tension side, not the slack side; expect more play on the slack side. Never use the alternator's main case as a pry point for adjustment. Use the front case (or better yet, an alternator-case holding tool to which the breaker bar will be attached), and don't overdo it.

Pulley Condition and Sizing

Does speeding up your metabolism make you lose weight?

Trying to boost your metabolism probably won't lead to weight loss. To lose weight, focus on reducing calories and increasing activity. Metabolism...

Last updated Sep 18, 2020

Does phentermine mess up your thyroid?

For people with history of hyperthyroidism: Tell your doctor if you have hyperthyroidism (an overactive thyroid). Phentermine may increase your...

Last updated Dec 27, 2020

Promotion

Pulley warpage, nicks, and normal wear take their toll on belts as quickly as poor alignment and improper tension. Pulleys should have a smooth wear pattern for 360 degrees and be free of any irregularities. Even a small nick or rise in the contact area will go through a belt in short order. A pulley with runout (warpage) has the same effect as improper alignment because it puts unacceptable side-loads on the belt. If you use a water-pump pulley that's too small and a crank pulley that's too large, you risk blowing cooling-system hoses because pump speed becomes excessive. The same can be said for the air-conditioning compressor and power-steering pump. When choosing pulley size, look to Ford for answers. Always opt for the same pulley sizes Ford used. See all 9 photos See all 9 photos This is a typical belt/pulley setup. Belt sidewall contact should be solid with each side of the sheath and at the same geometry. There should be an air gap below belt contact for heat dissipation. Each element of a V-belt performs a specific function: Tensile members (rayon cords) provide strength, while flexibility comes from the fabric and rubber composition. For example, high-performance engines such as the 289 High Performance, the Boss 302, and the 427, were fitted with larger pulleys to keep rotational speeds safe. We see this most with alternators, generators, and power-steering pumps.

Pulley Alignment

Improper alignment forces belts to operate in ways they weren't designed to function. Pulley misalignment, distortion, and misfit can go through a belt in a couple of hundred miles. When belts track normally through pulley sheaves, friction between the sheave and belt is reduced. Heat dissipates more quickly as the belt moves through pulleys when there's proper alignment. What's more, accessories such as alternators, water pumps, power-steering pumps, and air-conditioning compressors turn at normal operating speeds. When pulleys are misaligned, friction increases substantially, putting excessive side-loads on belts. The best indicator of pulley alignment is a straight edge along with temporary belt installation. The belt and straight edge should be parallel with the pulleys.

motortrend.com - Setting Proper Belt Alignment and Fit - Belt One On - MotorTrend

What can I drink in the morning for glowing skin?

6 Morning Drinks For Glowing Skin Lemon Water And Honey. Consuming lemon and honey with lukewarm water can work wonders for your skin. ... Fruit...

Last updated Apr 6, 2022

What is lower body lift surgery?

What is a lower body lift? This procedure, also known as a belt lipectomy, removes loose skin and fat from around your waist. It creates a firm,...

Last updated Apr 10, 2019

Promotion

Why do I weigh more than I look?

Muscle is denser than fat, and as it is more compact within your body, as you gain muscle mass, you end up looking thinner, no matter your physical...

Last updated Apr 8, 2019

Promotion

When will Ozempic be back?

The Therapeutic Goods Administration (TGA) has advised that semaglutide (sold as Ozempic) will be unavailable in Australia until the end of the...

Last updated Mar 25, 2022